The half round gutter is superior in transporting water compared to any other style. Water always collects to the absolute bottom of the gutter, and helps cleaning out debris and leaves. The thick 23 gauge galvanized steel with its unique bead design, makes it extremely strong yet light enough to have a quick install. Each gutter section is 10' long.

All miters are made from the same thick steel as the gutters for a perfect fit. These 90° inner miter are stamped out of 1 piece of metal, with absolutely no chance of leaking. No need to fill them with caulk that stops the water from flowing freely, these are smooth and absolutely leak free. Remember you will need two gutter connectors (GC) per miter.

All miters are made from the same thick steel as the gutters for a perfect fit. The 90° outside miters are stamped out of 1 piece of metal, with absolutely no chance of leaking. No need to fill them with caulk that stops the water from flowing freely, these are smooth and absolutely leak free. Remember you will need two gutter connectors (GC) per miter.

The 135° inside miter (or 45° depending on your measuring point) are great for your bay windows. Welded together and perfectly color matched, they are as the 90° miters completely caulk, rivet and screw free, and fits perfectly with the gutters creating an unobstructed flow from one gutter to the other. Remember you will need two gutter connectors (GC) per miter.

The 135° outside miter (or 45° depending on your measuring point) are great for your bay windows. Welded together and perfectly color matched, they are as the 90° miters completely caulk, rivet and screw free, and fits perfectly with the gutters creating an unobstructed flow from one gutter to the other. Remember you will need two gutter connectors (GC) per miter.

The gutter connector is amazing. With its EPDM rubber (same type of rubber that seals cars or truck doors) it connects gutters together, and gutter with miters in a matter of seconds. Hang it from the back of the gutters, pull it towards you and fold the tab over the bead. Leave a small gap (1/8") between the gutters. Lock it into place by pushing up and securing the tab, you are done. Do not put any caulk, rivet or screws in this product. The gutter connector allows for expansion and contraction of the system. By the way did you know that steel moves half as much, and half as fast as aluminum, and with the EPDM rubber always staying flexible you will have zero leaks. We recommend always ordering one or two extra gutter connectors for the job. Gives you some extra flexibility in your installation.

This end cap is universal, fits both left and right gutter ends. With the EPDM rubber gasket (same type of rubber that seals cars or truck doors) and the 4 flanges specifically developed to grip and seal, this is as easy as it gets. Simply align it over the bead and the backside of the gutter, slap it on with your hand or a rubber mallet. You can fold off the ear against the fascia if you have to. No caulking, crimping, rivets or screws to hold it in place. The EPDM seals and grips on tight, and you will have zero leaks.

This hanger is designed for a vertical fascia board installation. With steel being 1" thick and 1/5" wide they are super strong. Quick installation where you place the back edge of the gutter into the hanger and simply push the bead in and down into place. The exterior hanger allows for the fascia board to breathe and dry out, minimizing rotting problems that otherwise are common. Suited for all construction and remodeling, this hanger is tested to the highest standards and strength classification available. Fasten the hanger with 2 stainless or exterior screws, min 1 3/4" long, per hanger. Avoid protruding screw heads since they will interfere with the backside of the gutter in this type of hanger. Calculate with one hanger per two feet of gutter.

This hanger is designed for a vertical (plumb) fascia board installation. With steel being 1" thick and 1/5" wide they are super strong. The hanger follows the gutter beautifully. The hanger also allows for the fascia board to breathe and dry out, minimizing rotting problems that otherwise are common. The tabs on the hanger makes it perfectly suited for all construction, including remodeling and renovation. The hanger is tested to the highest standards and strength classification available. Fasten the hanger with 2 stainless or exterior screws, min 1 3/4" long, per hanger. This hanger can also be used on fascia boards 90° to the roof pitch. You can bend the short tail of the hanger if you need to. Works up to 12/12 pitch. Just remember on longer runs that the gutter will move farther in towards the siding, when sloped correctly. Calculate with one hanger per two feet of gutter.

The adjustable hanger is the perfect choice for fascia installations, when the fascia is 90° to the roof pitch. In other words not vertical (plumb). The hanger has 8 different positions. From low slopes up to 12/12 pitch. It actually also have a 0° setting which is for vertical (plumb) fascia installations. Typically if you have an installation requiring this hanger, but also have some sections with vertical fascia, you don't have to buy two different products. Calculate with one hanger per two feet of gutter.

This hanger is designed for on the roof installation. If you lack a fascia board, or have a steep roof pitch, a roof mounted hanger is recommended. Most of our hangers are made of the same material. With steel being 1" thick and 1/5" wide, these hangers are super strong. You need to use a hanger bender to bend the shaft to the correct angle. It is a quick installation where you place the back edge of the gutter into the hanger, and simply push the bead in and down into place. The hanger is tested to the highest standards and strength classification available. Calculate with one hanger per two feet of gutter.

This hanger is designed for on the roof installation. If you lack a fascia board, or have a steep roof pitch, a roof mounted hanger is recommended. Most of our hangers are made of the same material. With steel being 1" thick and 1/5" wide, these hangers are super strong. You need to use a hanger bender to bend the shaft to the correct angle. It is a quick installation where you place the back edge of the gutter into the hanger, and simply push the bead in and down into place. The hanger follows the gutter beautifully. The tabs on the hanger makes it perfectly suited for all construction, including remodeling and renovation. The hanger is tested to the highest standards and strength classification available. Calculate with one hanger per two feet of gutter.

The straight overflow protector can be placed anywhere in the gutter. Very easy to install with the tabs that fits over the bead of the gutter. Usable where you have concentrated drains from the gutter system on the higher roofs, flowing out on your lower roofs.

This overflow protector is used together with the inside miter. Typically where valleys come down with an increased water flow. Stops the water from gushing over, and redirects it into the gutter. Very easy to install with the tabs that fits over the bead of the inside miter.

The outlet is unbelievably easy to put on the gutter, simply stick the 90 degree tab into the bead of the gutter, roll it back and under the gutter. It will click into place and you finish with securing the tab down over the backside of the gutter. No caulking, no rivets or screws are needed to make this product work. The outlet is almost 9" wide on the gutter, allowing for a 6-7" whole to be cut in the gutter. The outlet guarantees free flowing water without any obstructions at all.

The round downspout is superior in transporting water from the gutter and out. Just ask any plumber why we all use round piping, it is simply the most efficient way of transporting fluids. Constructed from the same strong 23 gauge galvanized steel as the gutters, the double interlocking seam is super strong and the preshrunk end, overlaps 2" perfectly every time. Each downspout is 10' long.

The bridge is used between the elbows. It is pre-shrunk in both ends meaning these 3' sections are made to be cut. So one bridge gives you two pieces or bridges to work with. The pdf 'bridge lengths' is a support, and shows you roughly what lengths you will need. Measuring the distance between the elbows onsite is always the way to go. Remember to add 4" to the distance between the elbows before you cut.

This traditional downspout bracket is made of thick galvanized steel. It is hinged on one side, and has a screw on the other side. The legs protrude 1" so you always get air behind the downspout, and the siding is untouched.

A great product that simply wraps around the downspout, and have 2 locking positions. The first allows you to adjust the downspout, and the second tightens the product and wraps it securely around the downspout, holding it firmly in place. 2 brackets per downspout (10') is recommended. Should you damage your downspout, you can easily open the bracket to change the damaged downspout. Just take a flat head screw driver into the holes of the bracket and gently pry it open. The legs protrude 1" so you always get air behind the downspout, and the siding is untouched.

These elbows are a thing of beauty and a testament to the true engineering behind this system. The 70° angle is perfect for most buildings. The elbows are conical, and come with a male a female end that fits perfect every time, always overlapping 2". Two 70° elbows together, gives you approximately 7.5" of offset. The double seam is turned outside-in halfway through the arch, making the fit to elbows, outlets and downspouts extremely snug. There is no need for caulking or putting any rivets or screws into the system. In most other systems caulking and putting screws in the flow of water results in debris being clogged, increasing the risk for leaks.

This 85° elbow is conical and welded together for a perfect fit. Very usable for longer overhangs where you need to get back onto a wall, or vertical area to continue down. It has the same 2" overlap as the rest of the system making it very easy to install. Two 85 degree elbows together, gives you approximately 12" of offset. There is no need for caulking or putting any rivets or screws into the system. In most other systems caulking and putting screws in the flow of water results in debris being clogged, increasing the risk for leaks.

The Reinforced Bead Elbow fits in the system at the bottom of the downspout. The bottom lip is gently curled back, making the end smooth and gentle to the touch, keeping the smallest of persons and their curiosity in mind, no risk for cuts. The top is expanded to fit outside the large end of the downspout, should you have cut it to use the pre-shrunk end. To fix the RBE to the downspout, put a small tap screw in the back of the product. This is actually the only screw, you ever put into the system.

This product is designed to sit on top of the chute, covering the gap between the downspout and the chute, completing the Nordic system's sleek and savvy look. It fits outside of the downspout and can easily be moved up or down should you need to remove the chute for any reason. It also fits directly into the 4" ground pipes. Remember to place the lower downspout bracket with enough space left down to the DTE so you can move it up when needed. Also end the downspout halfway down into the DTE to allow it to move up.

The Chute is a self-cleaning leaf and debris product. Since the half round gutter system is so efficient in transporting everything out and down, especially with that 6-7" hole in the gutter allowing water and debris to flow extremely smooth into the outlet, this product separates and discards leaf and debris, out while allowing water to flow down through the grid. This is about as easy as cleaning gutter gets, self-cleaning. Fits perfectly into the standard 4" ground pipes or corrugated pipes.

The diverter is a product designed for having a water barrel collecting rainwater. The water can then be used on sunny days, giving you that gardener feeling whilst conserving both resources and money. Simply fold out the tongue when you wish to collect water, and fold it back up when the barrel is full. The diverter has an expanded top and shrunk bottom end, so inserting it into the downspout is easy. Like all other downspout related products, the overlaps are 2". There is no need for caulking or putting any rivets or screws into the system. In most other systems caulking and putting screws in the flow of water results in debris being clogged, increasing the risk for leaks.

The 4" offset is typically used to bridge over a lower protruding brick water table, or other constructions that requires you to move slightly from the center of your downspout. The 4" offset have an expanded top and shrunk bottom end to fit outside and inside the downspout. For reference the 70° elbows connected together gives you an 7.5" offset. There is no need for caulking or putting any rivets or screws into the system. In most other systems caulking and putting screws in the flow of water results in debris being clogged, increasing the risk for leaks.

The Y connector is very usable when you want to tie in more rooflines to one downspout. Sometimes you are restricted by construction and sometimes it is just more aesthetically appealing. You have a great allowance on you incoming angle (50°-80°) giving you lots of flexibility. The Y connector has an expanded top and shrunk bottom end, so inserting it into the downspout is easy. Like all other downspout related products, the overlaps are 2". There is no need for caulking or putting any rivets or screws into the system. In most other systems caulking and putting screws in the flow of water results in debris being clogged, increasing the risk for leaks.

The touch up paint is rich with primer coating characteristics, giving maximum protection where it is applied. Shake the bottle before applying the paint, once unscrewed attached to the lid is a small brush. The paint has been designed to dry quickly, and the bottle is small enough to be in your pocket when you are installing.